* * Due to changes
from the factory, some 2015-2016 models may require an open filter
aftermarket airbox as the changes in stock airbox may cause slight
clearance issues. * *
Genuine RK Sport Hood! Made in the USA! By one of the very best in the business!
Check out out store for part #402-278 if you want a nice AIRAID cold air intake kit to go with this hood.
- Functional Ram Air Scoop For Diesel Engine (Ram Air Cutout is on the passenger side under hood)
- Functional Heat extractor Vents
- Built In water management so any water getting in the vents is directed away from engine and wont cause any harm.
Here at Brody Dog Auto, we do not sell cheap low end hoods! Or
headaches you could call them! Over the years we have dealt with many
manufactures & weeded out the bad ones. We have seen and heard it
all. Nobody likes a headache & were not going to sell you one!
Form
and function
are perfectly blended in this fiberglass Ram Air Hood. The sporty lines
and assertive look of the center scoop give the Super Duty a distinctive
look
while the functionality of the scoop allows cool air to be channeled
into the engine compartment just over the factory air box. Heat
extraction vents look cool and aid in helping hot engine air vent. Cool
air is
more dense and burns more efficiently than hot air and can improve both
power and efficiency.
** Dealerships,clubs,organizations: We can ship additional hoods for no extra freight cost if shipped together.
All RK Sport Award Winning hoods are hand laid fiberglass and use stock hardware for
easy of installation.
- Replace your stock hood with a more stylish functional ram air hood.
- Besides the added cool looks, they have cool function in directing outside air to your air filter increasing performance!
- This hood has functional ram air ducting built in with functional
heat extractor vents/gills. (INCLUDES MESH GRILLES FOR SCOOP AND VENTS)
It is constructed from hand-laid fiberglass and high quality "ISO" resin.
Installs using stock hardware. Comes Gel Coated Gray ready to prep, prime and paint.
Made in USA Material: Fiberglass. Uses OEM hardware and Struts
Each hood comes with a one year warranty.
HOOD CONSTRUCTION;
Many
of our ram air hoods are constructed of hand-laid fiberglass, using
high quality "ISO resin" to give you the best possible quality in a
fiberglass hood. It comes with a smooth gel-coat finish, on both top and
underside surfaces.
All hinge and latch mountings are reinforced
with steel plates. All bolt holes are pre-drilled and tapped for easy
installation. To install these hoods, all you need to do is transfer
your stock hardware onto it and bolt it on to the factory hinges for
final alignment.
ISO resins are a higher quality, low shrink resin that allows the part to withstand more heat and prevent distortion.
SHIPPING INFORMATION:
-Hood Ships To All Lower 48 States
- ALL HOODS ARE BUILT AND SHIPPED TO ORDER
-Please allow approximately 10 business days before your hood ships
Frequently Asked Questions
Q 1: Will water get into my intake with your ram air hood?
A.
Our hoods have a built-in water management system to prevent water from
getting in. To date, we have not had a complaint of water getting into
an intake.
Q 2: What should I do if your product comes damaged?
A.
Even though we package our products very well, occasionally the freight
carrier will damage our product. In that case, refuse the shipment and
do not sign for it. It is expressly recommended that the package be
opened and inspected immediately upon receipt, even if the box looks
undamaged.
CAUTION!!! If you sign off with the freight carrier on a
damaged product, they will not honor any freight damage claim at a later
date and you will be held responsible.
CAUTION!!! If you are
having someone besides yourself receiving your package you must make it
clear to them that they are not to sign off with the freight carrier
until they have inspected the product and found it to be ok. If you have
to refuse our product because it was damaged, simply call us and we
will send you out another one ASAP. If you or someone else signs off on a
damaged product, we will not be held responsible. You must refuse it!
Q 4: Should I prefit your products before I have them painted?
A.
Yes, it is highly recommended that any hood be prefit before it is
painted. This is especially true with fiberglass parts. If you are not
the original owner it is possible that the vehicle was in a previous
accident, which could effect how our product fits you vehicle. Even new
vehicles are not all assembled exactly the same. Sometimes you have to
readjust your fenders and do other minor adjustments to make everything
right.